Explosion-proof camera system systems from Veilux are engineered for the most demanding hazardous environments, certified for Class I Division 1 and Zone 1 areas. Our explosion-proof camera system lineup meets ATEX, IECEx, and UL standards.
Oil tankers, FPSO vessels, and offshore platforms require ATEX- and IECEx-certified explosion-proof cameras for all equipment installed in cargo areas, on the main deck, and in enclosed machinery spaces classified as hazardous. The combination of hydrocarbon vapor, salt-air corrosion, wave immersion, vessel motion, and international maritime regulatory requirements makes marine hazardous area camera specification one of the most technically demanding application categories.
Veilux supplies explosion-proof camera systems to tanker operators, offshore contractors, and shipyards building or retrofitting vessels to ATEX/IECEx and OCIMF/SIRE standards. Our marine-experienced applications engineers understand flag state certification requirements, classification society rules, and SOLAS chapter II-2 obligations for pumproom monitoring and cargo deck surveillance.
Zone Classification on Oil Tankers
Explosion-proof camera system for Hazardous Locations
Tanker hazardous areas are classified per IEC 60092-502 and IEC 60079-10-1:
- Zone 1 (ATEX Category 2G): Entire cargo deck, within 3 meters of all tank openings, cargo manifold areas, enclosed pumproom. Requires explosion-proof (Ex d) equipment.
- Zone 2 (ATEX Category 3G): Extended deck perimeter beyond Zone 1 boundaries, spaces above the cargo deck to 2.4 meters. Zone 1 equipment is acceptable here and preferred for operational simplicity.
ATEX Category 2G / IECEx EPL Gb is the standard certification for all tanker cargo area cameras. North American flagged vessels use equivalent NEC Class I Division 1 ratings.
Key Surveillance Zones on Tankers
- Cargo deck and manifold area: Fixed cameras at each cargo manifold connection, plus PTZ cameras on elevated bridge wing positions for full-deck overview during cargo operations
- Enclosed pumproom: Minimum two cameras per SOLAS and OCIMF MEG4 guidance — overview of pump deck and cofferdam hatch/ladder. IP67 and anti-vibration mounts required.
- Bow and stern mooring stations: Fixed cameras for mooring operations safety monitoring and port security (ISPS Code compliance)
- Engine room and machinery spaces: Standard marine IP cameras (non-Ex) acceptable in non-classified machinery spaces; Zone 2 equipment for purifier rooms and fuel handling areas
Environmental Specifications for Marine Use
- 316L stainless steel or GRP (fiberglass) housings for cargo deck — aluminum corrodes in salt-air conditions within 2-3 years
- IP67 minimum; IP68 for cameras forward of amidships subject to wave wash
- IEC 60068-2-6 vibration tested for pumproom installations
- Operating temperature: -40 to +60 C for Arctic and Persian Gulf operations
Related Guides
- Explosion-Proof Camera Placement on Oil Tankers: Zone-by-Zone Guide
- Explosion-Proof Cameras on FPSO and Offshore Platforms
- ATEX vs. IECEx Certifications for Marine Installations
- Complete Guide to Explosion-Proof Cameras
Specifying cameras for a tanker or offshore vessel?
Veilux supplies ATEX/IECEx-certified explosion-proof camera systems matched to your vessel’s hazardous area classification, environmental conditions, and OCIMF/SIRE requirements.
For regulatory standards on explosion-proof camera system, refer to the OSHA hazardous location standards and NFPA 70 National Electrical Code.
All equipment in this category meets the rigorous safety requirements for classified hazardous locations. Independent certification to ATEX, IECEx, and UL standards verifies that each unit has been tested for use in explosive atmospheres found in petrochemical facilities, offshore platforms, grain handling operations, and chemical processing plants. These certifications are renewed on a defined schedule to reflect any design changes and to maintain compliance with evolving international standards.
Proper product selection depends on your site classification, mounting requirements, and operating environment. Class I Division 1 and Zone 1 environments demand the highest level of enclosure protection, while Division 2 and Zone 2 locations may permit designs with a lower protection level. Working with a certified hazardous-area specialist before finalising your specification helps ensure the installation meets both local electrical codes and applicable international standards without over-specifying the hardware.
Professional installation is strongly recommended for all hazardous-area equipment. Installers experienced with NEC Article 500 and IEC 60079 can verify that cable entries, conduit seals, and grounding connections are completed correctly and documented for compliance records. Veilux supplies full technical documentation, certified installation drawings, wiring diagrams, and post-installation support for every product in our catalog at no additional charge.
Routine inspection and preventive maintenance extend service life and preserve explosion-proof certifications. Key inspection points include housing integrity, cable gland condition, lens or cover glass condition, and confirmation that all enclosure fasteners meet published torque specifications. Veilux can assist with scheduled maintenance programs tailored to your facility type, operating cycle, and regulatory requirements, helping reduce unplanned downtime and extend the useful life of each installed unit.
Custom configurations are available for non-standard mounting geometries, extreme temperature ranges, or unique area classifications. Veilux engineers work directly with facility managers, EHS officers, and project engineers to develop solutions that meet both performance targets and compliance obligations. Contact our technical team to discuss your specific project requirements and receive a detailed equipment proposal, including complete bill of materials and compliance documentation for your approval process.
All equipment in this category meets the rigorous safety requirements for classified hazardous locations. Independent certification to ATEX, IECEx, and UL standards verifies that each unit has been tested for use in explosive atmospheres found in petrochemical facilities, offshore platforms, grain handling operations, and chemical processing plants. These certifications are renewed on a defined schedule to reflect any design changes and to maintain compliance with evolving international standards.